network

This module is used to initialize various network card drivers. The network card has the functions of connecting routing, disconnecting routing, viewing the connection information of the network card, and checking whether it is connected.

To use WiFi please make sure that the antenna is connected

esp8285)

On some development boards, a network card module that uses AT to interact, such as esp8285, is connected to k210 through a serial port

Pin 8 is the enable pin. You can create a GPIO object to control its high and low levels to achieve enable and disable, or you can use it to reset (low first and then high), and you need to wait for a while after reset Time to operate, You can view the routine network_espat.py

esp32)

Currently there is an esp32 module in the MaixDuino development board which is connected to k210 through spi
There is also a separate TF plug-in module

network.ESP8285(uart)

Construct an ESP8285 network card object. To use this method, you need to pass in a uart object. On the dock and GO currently supported by MaixPy, the AT command module is used as the WiFi. So the uart object is the object that communicates with the AT module, you can check the uart module routine

Calling this method will initialize ESP8285 and throw an exception if it fails

Parameters

  • uart: UART object communicating with AT module

return value

  • ESP8285: NIC object

ESP8285

connect(ssid, key)

Connect hotspot (AP/router)

Parameters

  • ssid: the SSID of the hotspot
  • key: hotspot password

return value

None, if an error occurs, an exception will be thrown

2.2. ifconfig

View wifi connection information, currently network does not support setting network card configuration

nic.ifconfig()

Parameters

no

return value

tuple type, elements are all strings: (ip, netmask, gateway, dns_server, dhcp_server, mac, ssid), if not found or invalid, the value is "0"

isconnected

Check if wifi is connected

nic.isconnected()

Parameters

no

return value

True: connected False: disconnect

disconnect

Disconnect wifi connection

Parameters

no

return value

no

scan

Scan the surrounding hotspot information

Parameters

no

return value

A list object, each element contains a string, the string comes from the response of the AT module, and the content is the same as described in the AT command document of esp8285, as follows: ecn, ssid, rssi,mac, channel, freq offset, freq cali, pairwise_cipher, group_cipher, bgn, wps

  • ecn: Encryption method
    • 0: OPEN
    • 1: WEP
    • 2: WPA_PSK
    • 3: WPA2_PSK
    • 4: WPA_WPA2_PSK *5: WPA2_Enterprise (Previously, AT does not support connecting to this encrypted AP)
  • ssid: string parameter, AP's SSID
  • rssi: signal strength
  • mac: string parameter, AP's MAC address
  • channel: channel number
  • freq offset: AP frequency offset, unit: kHz. Divide this value by 2.4 to get the ppm value
  • freq cali: frequency offset calibration value
  • pairwise_cipher:
    • 0: CIPHER_NONE
    • 1: CIPHER_WEP40
    • 2: CIPHER_WEP104
    • 3: CIPHER_TKIP
    • 4: CIPHER_CCMP
    • 5: CIPHER_TKIP_CCMP
    • 6: CIPHER_UNKNOWN
  • group_cipher: The definition is the same as pairwise_cipher
  • bgn: bit0 stands for b mode; bit1 stands for g mode; bit2 stands for n mode
       If the corresponding bit is 1, it means the mode is enabled; if the corresponding bit is 0, the mode is not enabled.
    
  • wps: 0, WPS is not enabled; 1, WPS is enabled

For example:

info_strs = ['4,"ChinaNet-lot0",-79,"c8:50:e9:e8:21:3e",1,-42,0,4,3,7,1', '4,"TOPSTEP2G4 ",-7
0,"f8:e7:1e:0d:0d:f8",1,-57,0,4,4,7,0']

This may seem strange, because the information of each AP is a string of characters, and there are integers and strings in the information. The strings are enclosed in double quotes, so after you get this string, you need to process it again. Use again, such as:

def wifi_deal_ap_info(info):
    res = []
    for ap_str in info:
        ap_str = ap_str.split(",")
        info_one = []
        for node in ap_str:
            if node.startswith('"'):
                info_one.append(node[1:-1])
            else:
                info_one.append(int(node))
        res.append(info_one)
    return res

info_strs = ['4,"ChinaNet-lot0",-79,"c8:50:e9:e8:21:3e",1,-42,0,4,3,7,1', '4,"TOPSTEP2G4 ",-70,"f8:e7:1e:0d:0d:f8",1,-57,0,4,4,7,0']

info = wifi_deal_ap_info(info_strs)
print(info)

The output is:

[[4,'ChinaNet-lot0', -79,'c8:50:e9:e8:21:3e', 1, -42, 0, 4, 3, 7, 1], [4,'TOPSTEP2G4', -70,'f8:e7:1e:0d:0d:f8', 1, -57, 0, 4, 4, 7, 0]]

Then for example, we need to get all the SSID of AP only need to use

for ap_info in info:
    print(ap_info[1])

enable_ap(ssid, key, chl=5, ecn=3)

  • Warning: As of November 26, 2020, MaixPy sockets have not yet implemented functions such as listen / bind / accpet.

Open hotspot

Parameters

  • ssid: SSID
  • key: password
  • chl: Channel number of WiFi signal
  • ecn: Encryption method, including OPEN``WPA2_PSK, etc., refer to the constant part of ESP8285 on this page, the default value is 3, which is ESP8285.WPA2_PSK, for example
    nic = network.ESP8285(uart)
    nic.enable_ap("maixpy", "12345678", 5, nic.OPEN)
    
    or
    nic.enable_ap("maixpy", "12345678", 5, network.ESP8285.OPEN)
    

disable_ap()

Turn off hotspot

Constant

OPEN

The hotspot encryption method does not require a password

WPA_PSK

The hotspot encryption method is WPA_PSK

WPA2_PSK

The hotspot encryption method is WPA2_PSK

WPA_WPA2_PSK

The encryption method of the hotspot is WPA_WPA2_PSK

Routine

Refer to routines in the network directory

network.ESP32_SPI(cs,rst,rdy,mosi,miso,sclk)

To construct an ESP32_SPI network card object, you need to pass in the corresponding GPIOHS FUNC

If the number of incoming parameters is incorrect, an error will be returned

Note If SPI and SD do not conflict on maixduino, you need to set ESP32_SPI as the hardware SPI configuration.

Parameters

  • fpioa_func corresponding to pin function

return value

  • ESP32_SPI network card object

ESP32_SPI

adc

Read the adc value of the esp32 module

Parameters

no

return value

tunple, the value of adc for 5 channels
The order is "PIN36", "PIN39", "PIN34", "PIN35", "PIN32"

Routine

demo_esp32_read_adc.py

network.WIZNET5K(spi, cs)

Construct a WIZNET5K network card object. To use this method, you need to pass in a spi object and a cs pin.

Calling this method will initialize WIZNET5K and throw an exception if it fails

Parameters

  • spi: Responsible for communication with WIZNET5K module
  • cs: spi communication chip selection footer

return value

  • WIZNET5K: NIC object

WIZNET5K

dhclient

DHCP dynamically obtain IP

nic.dhclient()

Parameters

no

return value

  • True: Get success
  • False: Get failed

ifconfig

nic.ifconfig()

Parameters

  • No reference: query network card information
  • Incoming (ip, netmask, gateway, dns_server) string tuple: configure network card, ip ip address, netmask subnet mask, gateway gateway IP address, dns_server DNS service IP address .

return value

  • No parameters: return tuple, the elements are all strings, (ip, netmask, gateway, dns_server), if not found or invalid, the value is "0"
  • Pass parameter: return None

isconnected

Check if the network is connected

nic.isconnected()

Parameters

no

return value

  • True: already connected
  • False: disconnect

Routine

network_wiznet5k.py