Drive RGB screen
Edit on 2022.04.12
RGB LCD display protocol is similar to VGA protocol, both have horizon synchronization signal line and vertical synchronization signal line. The main difference is that RGB LCD display protocol transfers by digital signal while VGA protocol transfers by analog signal.
Here we introduce VGA timing.
There shows horizon synchronization timing and vertical synchronization timing in the picture above.
From the timing picture, we know both display a horizon of data or display a vertical of data, data transfers during the two synchronization signal pulses.
Each horizon of data contains back porch, visible data (this is normally thought as active data) and front porch.
The visible data is resolution we normally think, while the parameter of back porch and front porch depends on the resolution and frame rate. Its typical parameters can be found in this web. http://www.tinyvga.com/vga-timing
The timing of this 5-inch screen we sell is a bit different, its parameters can be downloaded here. Detail book
For other size screen parameters, they can be downloaded here. Click me
The following picture shows the screenshot about this LCD timing.
The first picture form shows parameters of the screen and the the following picture is its timing.
From its timing picture, we can know we don't need to set front porch time and back proch time, we just need to set blanking time.
Please refer to this article to see how to create project.
Generate screen clock
- Here we use gowin official IP
The crystal oscillator onboard is 27MHz, but our screen needs 33.3MHZ clock, so we need to use the corresponding ip core to generate the corresponding clock.
Here we use
IP Core Generate which can be find in Tools -> IP Core Generate
rPLL and select Verilog in the pop-up window language, set CLKIN 27MHz, CLKOUT is 33.00MHz. Also config the tolerance.
After click OK it asks whether add it to current project, here we choose yes.
Then a tmp file will appear, we can use it to generate the ip, like what is shown below.
- To start this we should create a verilog file first
First define ports which are needed to drive screen
module VGAMod ( input CLK, input nRST, input PixelClk, output LCD_DE, output LCD_HSYNC, output LCD_VSYNC, output [4:0] LCD_B, output [5:0] LCD_G, output [4:0] LCD_R );
We use RGB565 driver mode.
Then we define the constants according to the timing form picture
localparam V_BackPorch = 16'd6; //0 or 45 localparam V_Pluse = 16'd5; localparam HightPixel = 16'd480; localparam V_FrontPorch= 16'd62; //45 or 0 localparam H_BackPorch = 16'd182; localparam H_Pluse = 16'd1; localparam WidthPixel = 16'd800; localparam H_FrontPorch= 16'd210; localparam PixelForHS = WidthPixel + H_BackPorch + H_FrontPorch; localparam LineForVS = HightPixel + V_BackPorch + V_FrontPorch;
First we define front porch, back porch and valid pixel data.
As for the front porch timing and back porch timing which have been mentioned earlier, it can be combined into an erasing time, that is, one can be set to 0, and the other can be set to the erasing time. Anyway, the front porch timing and back porch timing can be added up to meet the timing requirements in the table is ok.
- Define some variables helps us to meet timing requirment
reg [15:0] LineCount; reg [15:0] PixelCount; reg [9:0] Data_R; reg [9:0] Data_G; reg [9:0] Data_B;
This code generates synchronization signals. It should be noted that the synchronization signals of this screen enabled by negative polarity
always @( posedge PixelClk or negedge nRST )begin if( !nRST ) begin LineCount <= 16'b0; PixelCount <= 16'b0; end else if( PixelCount == PixelForHS ) begin PixelCount <= 16'b0; LineCount <= LineCount + 1'b1; end else if( LineCount == LineForVS ) begin LineCount <= 16'b0; PixelCount <= 16'b0; end else PixelCount <= PixelCount + 1'b1; end always @( posedge PixelClk or negedge nRST )begin if( !nRST ) begin Data_R <= 9'b0; Data_G <= 9'b0; Data_B <= 9'b0; end else begin end end //Here note the negative polarity of HSYNC and VSYNC assign LCD_HSYNC = (( PixelCount >= H_Pluse)&&( PixelCount <= (PixelForHS-H_FrontPorch))) ? 1'b0 : 1'b1; assign LCD_VSYNC = ((( LineCount >= V_Pluse )&&( LineCount <= (LineForVS-0) )) ) ? 1'b0 : 1'b1;
- This code decides whether display image.
This driver needs a port which is set to 1 when the 800*480 data of the image is valid to enable display.
assign LCD_DE = ( ( PixelCount >= H_BackPorch )&& ( PixelCount <= PixelForHS-H_FrontPorch ) && ( LineCount >= V_BackPorch ) && ( LineCount <= LineForVS-V_FrontPorch-1 )) ? 1'b1 : 1'b0; //It will shake if there not minus one
Test color bars
- This code generate color bars to test LCD
assign LCD_R = (PixelCount<200)? 5'b00000 : (PixelCount<240 ? 5'b00001 : (PixelCount<280 ? 5'b00010 : (PixelCount<320 ? 5'b00100 : (PixelCount<360 ? 5'b01000 : (PixelCount<400 ? 5'b10000 : 5'b00000 ))))); assign LCD_G = (PixelCount<400)? 6'b000000 : (PixelCount<440 ? 6'b000001 : (PixelCount<480 ? 6'b000010 : (PixelCount<520 ? 6'b000100 : (PixelCount<560 ? 6'b001000 : (PixelCount<600 ? 6'b010000 : (PixelCount<640 ? 6'b100000 : 6'b000000 )))))); assign LCD_B = (PixelCount<640)? 5'b00000 : (PixelCount<680 ? 5'b00001 : (PixelCount<720 ? 5'b00010 : (PixelCount<760 ? 5'b00100 : (PixelCount<800 ? 5'b01000 : (PixelCount<840 ? 5'b10000 : 5'b00000 )))));
Do not forget to add endmodule in the end of the driver file
Up to now we have finished the driver module.
Instantiated in the top
- New a verilog file
- Just copy the content below and save it is ok
module TOP //Name TOP module ( input nRST, input XTAL_IN, output LCD_CLK, output LCD_HYNC, output LCD_SYNC, output LCD_DEN, output [4:0] LCD_R, output [5:0] LCD_G, output [4:0] LCD_B ); // list ports wire CLK_SYS; wire CLK_PIX; //instantiate pll Gowin_rPLL chip_pll( .clkout(CLK_SYS), //output clkout //200M .clkoutd(CLK_PIX), //output clkoutd //33.00M .clkin(XTAL_IN) //input clkin ); VGAMod VGAMod_inst //instantiate vga driver ( .CLK ( CLK_SYS ), .nRST ( nRST ), .PixelClk ( CLK_PIX ), .LCD_DE ( LCD_DEN ), .LCD_HSYNC ( LCD_HYNC ), .LCD_VSYNC ( LCD_SYNC ), .LCD_B ( LCD_B ), .LCD_G ( LCD_G ), .LCD_R ( LCD_R ) ); assign LCD_CLK = CLK_PIX; endmodule
Synthesize, constrain, Place&Route
After finishing steps above, go to the "Process" interface, systhesize the edited file, which means running "Systhesize".
If the result is the same as shown below
It means that there is no bug in our code, we can continue the next steps.
If there is some thing wrong, please fix by yourself.
- Here we only constraint pins
The corresponding pins and ports are as follows form shows
The way to constain pins can refer to the Light led, it contains a way to constain pins.
If you feel troublesome about the method above, you can copy the content in this page， and paste it in ".cst" file in this project (If there is no ".cst" file, just create a "physicsl constrains file").
After constraining, we need to open IO mux to complete Place&Route.
Tick Project -> Configuration -> Place&Route -> Dual-Purpose Pin which is in the Menu Bar.
Then we can run Place&Route.
Finishing Place&Route, we can download the generated .fs file to the development board to see color bar.
Now the tutorial ends, if you have any suggestions, just leave a message.